bike / saddle-height

Bike Saddle Height Calculator

Enter your inseam to get a starting saddle height by the LeMond and 109% methods, the range between them, and the knee angle targets to fine tune it.

Inputs
LeMond, BB to top of saddle
75.1 cm
29.6 in
109%, BB to top of saddle
75.4 cm
29.7 in; pedal to saddle 92.7 cm

Starting range: 75.1 cm to 75.4 cm, bottom bracket to top of saddle, from the lower to the higher of the two methods. Fine tune within it, or beyond it, by the knee angle below.

Road: the heights above are the starting point; fine tune with the knee angle.

172.5 mm cranks unless you pick another length (site convention). The formulas are starting points; the knee angle decides.

Knee angle targets

Fine tune the starting height until the knee bend at the bottom of the stroke falls in a target range. Use the range that matches how you measure.

MethodHow it is measuredKnee bend
HolmesStatic, pedal at the bottom, measured with a goniometer25 to 35°
Ferrer-Roca et al.Dynamic, while pedalling30 to 40°
Millour et al.Dynamic, pedal at the bottom, on video33 to 43°

Do not compare a static measurement with a dynamic target. Millour et al. found the dynamic knee angle 8° greater than the static one with the pedal at the bottom, so a knee that reads in the static range on a goniometer can read below the dynamic range on video.

What the two heights measure

Both are measured along the seat tube to the top of the saddle, where you sit. Bottom bracket to top of saddle starts at the centre of the crank axle; that is the height LeMond's formula gives and the one to set with a tape measure. Pedal to saddle starts at the pedal axle with the crank at the bottom, in line with the seat tube; that is what the 109% method gives, so the calculator subtracts the crank length to put it on the same footing (site convention: straight line geometry, the seat tube angle ignored).

Which method to trust

Both formulas are starting points, not answers. In Peveler and colleagues' study, saddle height set at 109% of inseam fell outside the 25 to 35° knee angle range 63% of the time, in 9 trained cyclists and 18 non cyclists. Bini, Hume and Croft's review lists the LeMond and heel methods among those in use, notes that the studies used small samples, and suggests setting the height by knee flexion angle, 25 to 30°. In a later study by Peveler, oxygen uptake was lower with the saddle set at a 25° knee angle than at 35° or at 109% of inseam.

LeMond's factor of 0.883 is the one widely quoted from Greg LeMond's 1987 book; we could not check the book itself, so on this page it is a site convention. Small samples in all of these studies mean the knee angle on your own bike decides.

How to measure your inseam

  1. Stand against a wall. Stand barefoot with your back and heels against a wall, feet about as far apart as on the pedals.
  2. Put a book between your legs. Pull a hardback book up firmly between your legs, spine up and level, the way a saddle presses when you sit.
  3. Mark the top of the book. Hold the book still and mark the wall at the top edge of its spine.
  4. Measure to the floor. Measure from the floor to the mark. Measure twice; if the two differ, measure a third time and use the two that agree.

This is the usual fitting practice, not a standard. Measure in the same way each time, because a few millimetres of inseam move the result.

Crank length, shoes and cleats

The calculator assumes 172.5 mm cranks unless you pick another length (site convention). The 109% height is measured from the pedal, so a crank 5 mm longer puts the saddle 5 mm lower above the bottom bracket; LeMond's formula does not use crank length. Shoes, pedals and cleats change how far your foot sits above the pedal axle: after changing any of them, check the knee angle again (site convention). Set the cleats with the cleat position calculator and the cleat setup guide. Moving the saddle back or changing its tilt changes the effective height too, so check again after either (site convention).

Height is half of the saddle fit; for the other half, find your width with the saddle width calculator.

Road, gravel, MTB and TT

No source we read gives a different saddle height by bike type, so the calculator gives the same starting heights for all four and the bike choice only changes the note under the result. On a mountain bike with a dropper post, the result is the height with the post fully extended (site convention). On a TT or triathlon bike the position rotates forward; set the height by the knee angle on that bike rather than by a fixed correction (site convention).

SAFETY: Never raise the seatpost so far that its minimum insertion mark shows above the frame. Tighten the seatpost clamp to the torque printed on the frame or the seatpost, or given in their manuals. Change one thing at a time, a few millimetres at a time.

If riding hurts, see saddle pain and back pain.

Where these numbers come from

The studies are quoted from their PubMed abstracts, checked on 16 November 2026.

Frequently asked questions

How high should my bike seat be?

Start with 0.883 times your inseam, from the centre of the bottom bracket to the top of the saddle along the seat tube, and check it against 109% of inseam measured from the pedal. For an 85 cm (33.5 in) inseam that gives 75.1 cm (29.6 in) and 75.4 cm (29.7 in) with 172.5 mm cranks. Then fine tune with the knee angle: 25 to 35° with the pedal at the bottom, measured static.

LeMond or 109%: which saddle height formula is better?

Neither is more than a starting point. The 109% method fell outside the 25 to 35° knee angle range 63% of the time in Peveler and colleagues' study of 27 riders, and Bini, Hume and Croft's review notes that the studies used small samples. This calculator gives both and a range between them; the knee angle decides.

What is the heel method for saddle height?

Sit on the saddle and put your heel on the pedal with the crank at the bottom: your leg should be just straight. Riding on the ball of the foot then leaves a slight bend at the knee. It is a quick check, not a formula, and Bini, Hume and Croft list it among the methods in use.

Does crank length change saddle height?

For the 109% method, yes: the height is measured from the pedal, so a crank 5 mm longer puts the saddle 5 mm lower above the bottom bracket (74.9 cm (29.5 in) instead of 75.4 cm (29.7 in) for an 85 cm inseam). LeMond's formula does not use crank length. Either way, check the knee angle after a crank change.

Should my MTB saddle be lower than on my road bike?

No source we read gives a lower saddle height for mountain bikes, so this calculator gives the same starting height for every bike. With a dropper post, set the height for the post fully extended; that is this site's convention, not a published rule.

How do I measure my knee angle?

With the bike on a trainer, put the crank at the bottom of the stroke and measure the angle between the thigh and the lower leg with a goniometer: a straight leg is 0°. Holmes's target for this static measure is 25 to 35°. Measured on video while pedalling, the angle reads larger, about 8° (Millour et al.), so use a dynamic target such as 33 to 43° for video.

Related tools

Set your cleats with the cleat position calculator, troubleshoot with saddle pain, back pain and hand numbness. All bike tools are on the bike page.

Last updated: November 2026