ski / how to adjust ski bindings
How to Adjust Ski Bindings to Your Boots
The order of the work, from boot sole to release check, with what the binding makers' own manuals say at each step.
How do you adjust ski bindings? Check that the boot sole fits the binding, read the boot sole length, set the toe and heel to it, check the forward pressure and the toe height, then set the DIN on toe and heel to the same value. Finish with a function check, and have a shop measure the release force on a calibrated test device. Atomic says binding adjustments should always be carried out by an authorized dealer, and Look requires a trained technician.
How to adjust ski bindings, step by step
1. Check that the boot sole fits the binding
Read the sole standard on the boot and the marking on the binding. An alpine sole (ISO 5355) and a walk sole (ISO 23223, sold as GripWalk) go only in bindings made for them, and Look's 2022/23 manual says not to use alpine touring boots with an ISO 9523 sole in its alpine bindings. If the sole and the binding do not match, stop here and check your boot and binding in the ski binding compatibility checker.
2. Find your boot sole length
The boot sole length (BSL) is printed on the side of the shell, usually at the heel, in millimetres. It is the length the binding is set to, not your shoe size. If the marking has worn off, a shop can measure the sole.
3. Set the toe and heel to the sole length
On most alpine bindings one piece slides along a track marked with sole lengths: set it to your boot sole length and lock it. On the Look Konect, for example, the 2022/23 manual says to align the rear of the toe piece with the corresponding boot sole length mark. How the piece moves and locks differs between models, so follow the manual of your binding. If your sole length is outside the range of the track, the binding has to be remounted, which is a job for a shop.
4. Check the forward pressure
Forward pressure is how firmly the heel piece holds the boot against the toe piece. With the boot clicked in, the forward pressure indicator must sit in the range your binding's manual gives, and what that looks like differs by brand. Step out and back in and look again. Look's manual also warns not to over tighten forward pressure.
Examples from manufacturer manuals of earlier seasons; check the manual of your binding.
| Brand | Model | Manual (season) | What OK looks like |
|---|---|---|---|
| Marker | Jester, Griffon, Squire ID | Marker, 2017/18 | "Check if the forward pressure adjustment screw is flush with the back of the heel housing." |
| Salomon, Atomic, Armada | Warden MNC, STH2, Strive 14 GW | Armada, 2023 | "adjust the forward pressure to align the top of the head screw with the back of the heel part" |
| Look | SPX | Look, 2022/23 | "OK = The yellow indicator covers half of the window" |
| Look | NX | Look, 2022/23 | "OK = The scribed mark is in the middle of the window" |
| Look | Pivot | Look, 2022/23 | "OK = The white (or yellow) indicator tab aligns with, or just past, the two raised scribes" |
| Tyrolia, Elan | Elan manual | Elan, 2024/25 | the indicator "should rest in the marked" area |
5. Check the toe height
On many bindings the toe height sets itself: Look's 2022/23 manual says the toe height and width automatically adjusts for ISO 5355 and ISO 23223 soles. Where it is set by hand, Marker's 2017/18 manual gives a gap of 0.5 mm between the boot sole and the gliding AFD, checked with a strip of paper that pulls out just before it tears. On some Elan and Tyrolia bindings a screwdriver icon means the toe height is for a technician to set. Set it by the gap, not by the direction you turn the screw: that differs between models.
6. Set the DIN on the toe and the heel
First calculate your DIN setting. Then turn the adjustment screw on the toe piece until the indicator shows that number, and do the same on the heel piece: toe and heel take the same value. Watch the indicator, not the direction you turn the screw: bindings differ from brand to brand.
7. Check function, and have the release force measured
Check function, not release force. Step in and out a few times: the heel should close with a firm snap, the brake should retract and spring back, and the forward pressure indicator should stay in range. A hand twist cannot confirm your DIN, and many correctly set bindings will not release by hand, so do not throw your weight forward to force a release. Only a shop's calibrated test device measures release torque (ISO 11088): Armada's technical manual has the shop measure the twist and forward lean torque values with it. Marker asks skiers to bring the binding to an authorized retailer for inspection before the beginning of each ski season.
Tools
Most binding screws take a Pozidriv No. 3 screwdriver. Marker's 2017/18 manual says Marker recommends adjustment with a Pozidriv 3 screwdriver, Salomon's 2017/18 manual says a Pozidriv No. 3 screwdriver, not a Phillips, must be used, and Look's 2022/23 manual lists a #3 Pozidrive. Some models take a #3 flat head (Look) or a Torx bit (Powder), so check the screw head before you start.
Adjusting bindings for new boots
New boots almost always mean a new boot sole length. Repeat steps 2 to 4: read the new sole length on the shell, set the toe and heel to it, and check the forward pressure. Then work out the DIN again, because sole length is part of it, and set it on toe and heel. If the new sole length is outside the range of the binding's track, the binding has to be remounted on the ski, which is a job for a shop.
Where these numbers come from
Every quote on this page was checked against the maker's document on 16 November 2026. The manuals are copies held by dealers, from the seasons named; the manual of your own binding outranks them.
- Atomic, Understanding ski binding adjustment: binding adjustments by an authorized dealer.
- Look, Binding Technical Manual 2022/23: the Technical Review for anyone adjusting Look or Rossignol bindings, the Konect sole length mark, the SPX, NX and Pivot forward pressure indicators, the toe height that adjusts itself, ISO 9523 touring soles, the #3 Pozidrive and #3 flat head.
- Marker, Technical Manual 2017/18: the Pozidriv 3 screwdriver, the forward pressure screw flush with the heel housing, the gap at the AFD and the paper strip, the inspection before each season.
- Armada (Salomon), Technical Manual 2023: the forward pressure screw on Salomon, Atomic and Armada heels, and the twist and forward lean torque measured on a calibrated testing device.
- Salomon, Technical Manual Alpine 2017/18: a Pozidriv No. 3, not a Phillips.
- Elan, Technical Manual 2024/25 (Tyrolia and Elan bindings): the forward pressure indicator and the toe height icon on Tyrolia and Elan bindings.
- The order of the steps, and the advice to watch the indicator rather than the direction of the screw, are this site's reading of these manuals; none of them gives a turning direction.
Frequently asked questions
Can I adjust my own ski bindings?
You can learn the steps and see what each one does, but the makers say the work belongs with a trained technician. Atomic says binding adjustments should always be carried out by an authorized dealer, and Look requires anyone mounting or adjusting its bindings to have completed its Technical Review. Our advice: learn the steps, and leave the release force check and any remounting to a shop with a calibrated test device.
Do I need to adjust my bindings for new boots?
Yes. A new boot usually has a different sole length, so the toe and heel have to be set to it and the forward pressure checked again (steps 2 to 4). The DIN can change too, because sole length is part of it, so work it out again and have the release force checked. If the new sole length is outside the range of the binding, it has to be remounted.
What tools do I need to adjust ski bindings?
Usually a Pozidriv No. 3 screwdriver. Marker recommends one, Salomon's 2017/18 manual says a Pozidriv No. 3 and not a Phillips must be used, and Look's 2022/23 manual lists one too. Some models take a flat head or a Torx bit instead, so check the screw head first (see Tools above).
How far can ski bindings be adjusted?
As far as the sole length scale on the binding's track goes, and that range differs between models. If your boot sole length is outside it, the binding has to be remounted on the ski, which is a job for a shop.
Which way do I turn the screw to raise the DIN?
There is no rule to go by: none of the binding manuals we read gives a direction, and bindings differ from brand to brand. Turn the screw and watch the indicator until it shows your setting, on the toe and on the heel.
Related Ski Tools
- Work out your release setting with the DIN calculator.
- Check that your boot sole fits your binding with the ski binding compatibility checker.
- Find your boot size and sole length with the ski boot size calculator.
- Worn soles change how a binding releases: check your boots with the ski boot retirement checker.
Last updated: November 2026